Return to Home

INDUSTRIAL MELTING ~ HEAT TREAT FURNACES  AND ACCESSORIES

Bench Rammers

The problem of rammer breakage with the original aluminum hand rammer has been corrected by using a more ductile analysis of aluminum. The illustration "A" shows the angle of bend the rammers will withstand. Rammer is available with a molded peen end shown in illustration "B". The 14" rammer has a molded replaceable peen end.
 

Bell Plunger

Bell Plunger is heavy cast iron. Bell is 4" in diameter with a 30" handle. For degassing and deoxidizing molten metal.
Approximate Weight: 4 lbs. Part No. 031630
Available with 6" handle. Part No. 031622

Skimmer (all purpose)

Skimmer is 4" in diameter. Skimmer head is made of stainless steel. Handle is 30" long. Approximate Weight: 3 lbs. Part No. 031670

Pouring Ladles (For Aluminum Only)

MIFCO pouring ladles are pressed steel with black pipe handles and are available in the following sizes:

 

Part No.

Diameter

Cap. of Alum.

Approx. Wt.

031626

7-3/4"

6 lbs.

11 lbs.

031627

8"

8 lbs.

15 lbs.

031628

9"

12 lbs.

19 lbs.

 

Tool Kits for Molders Benches

MKB-2 Tool Kit for MB-2 Molders Bench (Part #033550)

2 - Aluminum Rammers 2 - 7/8" Sprue Cutters
2 - M-5 Tool Kits 1 - Parting Dust 10# with Bags
2 - Molders Bellows (10") 2 - Molders Shovels (10")
1 - Hand Riddle (18" diameter x #4 mesh) 2 - Hand Riddles (18" diameter x #8 mesh)
1 - 24" Strike-off Bar  

MKB-1 Tool Kit for MB-1 Molders Bench (Part #033650)

1 - Aluminum Rammer 1 - 7/8" Sprue Cutters
1 - M-5 Tool Kit 1 - Parting Dust 10# with Bags
1 - Molders Bellows (10") 1 - Molders Shovel (10")
1 - Hand Riddle (18" diameter x #4 mesh) 1 - Hand Riddle (18" diameter x #8 mesh)
1 - 24" Strike-off Bar  
 

Oil Bonded - Pre-Mixed Foundry Sand

 

Sold in 40lb. Buckets - Ready to Use

Molders Tool Sets

Call for pricing on individual tools.

Set # M-5 (Part Number 031610):
One each of the following items:
1" x 5" Round Point Trowel
1" Gate Cutter & Spoon
1" Slick & Oval
1" Slick & Square
3/8" x 14" Lifter

Set # M-9 (Part Number 031611):
One each of the following items:
1-1/4" x 5" Square Trowel
1" Gate Cutter & Spoon
1" Slick & Oval
1" Slick & Square
1-1/4" x 5" Round Point Trowel
1" Heart & Leaf
1" Taper & Leaf
3/8" x 14" Lifter
3-3/4" x 14" Bench Rammer

 

Sectional Grid Pouring Floor

In Safe Foundry Practice, you should not pour into molds which are on a concrete floor. This practice is dangerous because the molten metal spilled on the floor will cause chunks of concrete to blow out of the floor surface under the molten metal, throwing hot metal and concrete upward onto the operator. If you notice, in foundries, you will never see them pour on anything but dirt floors or over a grid. In most schools, the foundry area seems to be an after thought because there is never a safe pouring area built into the floor. For this reason, the makers of MIFCO furnaces, safety tongs and shanks, have come out with another product to make the foundry safer. The Sectional Steel Grid Pouring Floor is made up of 2' x 4' sections that are fastened together. When laid on the floor side by side they give you a pouring floor that is 4' wide and as long as you want it. The grid floor can be laid in minutes. Spread the sand between the grids and the pouring area is ready for the foundry session whether it is a day, six weeks or a year. When the foundry session is over, just pick up the grids, sweep up the sand and the area is clean again.

MIFCO STORE
BUY ONLINE

Click For Parts, Accessories and Safety Clothing

 

SPECIAL ANNOUNCEMENTS

 

Make an Email inquiry on a product

 

 

 

 

Telephone (Sales): 217-446-0941 ~ Fax 217 446-0943
Created by   for McEnglevan Industrial Furnace Company, Inc ~ All Rights Reserved 2008
By use of this Website you agree to our ACCEPTABLE USE Policies-Copyright Restrictions